navigation system RENAULT TWINGO RS 2009 2.G Electrical Equipment - Radio R01-08 Workshop Manual

86A-33
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF006
PRESENT
OR
STOREDFM1 AMPLI
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system is switched on using the on/
off button.
The fault can only be detected if the battery voltage is between:
12 V < X < 15 V.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
If the vehicle is equipped with a navigation system, go on to Part B, otherwise go to Part A.
Part A:
Check the connection and condition of the aerial connectors on the radio, component code 261, and on the roof
aerial connector, component code 1208.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34AN between components 261 and 1208,
•TB13 between components 261 and 1208.
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the roof aerial amplifier, component code 1208 (see MR 392 (Clio III) or MR
411 (New Twingo) Mechanical, 86A, Radio, Radio aerial: Removal - Refitting).
If the fault is still present, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R108_VA4_DF006

86A-34
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF006
CONTINUED
Part B:
Check the connection and condition of the aerial connectors on the radio and navigation system, component codes
261 and 662, and of the connector on the roof aerial, component code 1874.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•46CJ between components 261 and 662,
•TB82 between components 261 and 662.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34EP between components 261 and 1874,
•TB39 between components 261 and 1874.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the roof aerial amplifier, component code 1874 (see MR 392, Mechanical,
86A, Radio, Radio aerial: Removal - Refitting).
If the fault is still present, replace the radio (see MR 392, Mechanical, 86A, Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.

86A-46
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R108_VA4_DF064

86A-60
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
86A
R01-08
Vdiag No.: A4
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated and
radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit,
Fault finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R108_VA4_ALP1
RADIO
Fault finding – Fault Finding Chart

86A-62
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 1
CONTINUED 2
Check the continuity, insulation and absence of
interference resistance on the following
connection:
•34HU between components 261 and 1714.
If the connection is faulty and there is
a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC between components 662 and 261,
•34GB between components 662 and 261.If the connection or connections are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC and 107X between components 261
and 1714,
•34GB and 107W between components 261
and 1714.Replace the navigation computer,
component code 662 (see MR 392,
Mechanical, 83C, On-board telematics
system, Navigation computer:
Removal – Refitting). Are the checks correct?
Replace the radio, component code 261 (see MR
392, Mechanical, 86A, Radio, Radio: Removal -
Refitting).
C
YES
NO
YES
NO
YES
NO
YES

86A-69
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 1
CONTINUED 9
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC and 107X between components 261
and 1714,
•34GB and 107W between components 261
and 1714.Replace the navigation computer,
component code 662 (see MR 392
(Clio III) Mechanical, 83C, On-board
telematics system, Navigation
computer: Removal – Refitting). Are the checks correct?
Replace the radio, component code 261
(see MR 392, Mechanical, 86A, Radio,
Radio: Removal - Refitting).
Is the fault still present?The problem disappears.
Replace the multimedia connection unit, component
code 1714 (see MR 392, Mechanical, 83C, On-
board telematics system, Multimedia network
interface unit: Removal - Refitting).
J
YES
NO
YES
NO
YES

86A-77
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 6 Radio reception fault.
NOTESFor the aerial, use component code 1874 for a vehicle equipped with a navigation
system, and 1208 for a vehicle without this option.
See Clio III or New Twingo wiring diagrams.
See Clio III or New Twingo wiring diagrams.
Check the presence and condition of the radio
aerial.Replace the radio aerial, component code
1208 or 1874 (see MR 392, 86A, Radio, Radio
aerial: Removal - Refitting) for New Twingo
or (see MR 411, 86A, Radio, Radio aerial:
Removal - Refitting) for Clio III. Is the radio aerial correct?
Check the condition of the connections of the
radio aerial coaxial cable at the radio aerial,
component code 1208 or 1874 and of the radio,
component code 261.
Are the connections correct?If the connectors are faulty and if there is a
repair procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair) repair the
connector(s); otherwise, replace the wiring.
NO
YES
NO
YES
A
R108_VA4_ALP6

86A-80
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 8Backlighting does not change when the vehicle lights are
switched on
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
NOTE: Switch on the side lights and position the lighting rheostat wheel in the centre
position.
The display, component code 653, is only available when the vehicle does not have
the navigation function.
The multimedia connection unit, component code 1714, is only available when the
vehicle has the navigation function.
Check the backlighting of the following components:
radio, display and instrument panel.
Are all of the components backlit?
Attempt to backlight these components
once again, and if no conclusion can be
made, contact the Techline.
Does the instrument panel light up?Perform fault finding on the instrument
panel (see 83A, Instrument panel).
YES
NO
NO
YES
A
R108_VA4_ALP8

86A-90
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 15 Fault when using the mobile connectivity terminal
NOTESSee Clio III or New Twingo wiring diagrams.
ALP 15 is used to run fault finding on the mobile connectivity terminal if a mobile
connectivity computer is not fitted on the vehicle.
In a vehicle equipped with a navigation computer, the terminal is connected to the
navigation computer, component code 662. Otherwise, it is connected to the radio,
component code 261.
Is the mobile device connected to the mobile connectivity
terminal switched on and is the volume sufficient?Increase the volume of the
mobile device.
Does the customer's mobile device operate correctly with
earphones that are in good condition?Explain to the customer that the
mobile device is defective.
Check the condition (appearance check) of the cable
connecting the mobile device to the analogue terminal.
Explain to the customer that the
cable of the mobile device is
faulty. Are the checks correct?
NO
YES
NO
YES
NO
YES
A
R108_VA4_ALP15